The cold water (freezing) machine displays the reverse phase loss fault quick troubleshooting
The cold water (freezing) machine shows a reverse phase loss fault, which is a common fault of abnormal power supply. The reason for this failure is simple, and it is very convenient to repair, as long as there is a little electrician foundation, it can be easily solved!
The power supply of the chiller (freezer) is powered by a three-phase four-wire system. There are directional restrictions in the operation of some electrical accessories of the equipment. Besides, the motor is not allowed to run without phase, which will cause mechanical failure or burn the motor coil. Therefore, the chiller manufacturers have installed power protection devices (phase sequence and phase failure protection relays).
The failure of "reverse phase loss" is nothing more than the following conditions:
One, the power protector is broken
When the equipment is normally powered on, close the air switch in the control box. At this time, the indicator light on the power protector will light up (red means power is supplied, yellow means power is normal), if only the red light is on, it means three One phase power supply is missing or the three-phase power supply sequence is incorrect. If it is confirmed that the power supply is normal, but the indicator light of the power protector is off, it means that the protector is damaged.
The power protector is located in the control box. Open the control box panel, you can see an accessory with the word "RD6" on it. This is the power protector. As shown below:
Treatment: Determine whether the phase is missing or reversed according to the light on the protector. Use a multimeter to find out the cause of one less phase of the three-phase power supply and eliminate it, or change the order of the three-phase power supply (change the order of the two at will). Or replace the power protector.
Two, power supply lack of phase or phase sequence reversed
This problem can be basically judged by our power protector. When the power protector only has a red light on, it can basically be regarded as a lack of phase or a reverse phase sequence.
deal with:
Check the three-phase power supply with a multimeter to find out the cause of the lack of phase. Or change the order of any two of the three-phase power supply.
The cold water (freezing) machine displays the reverse phase loss fault quick troubleshooting
Recent related posts
-
08/08/2020
The cold water (freezing) machine displays the reverse phase loss fault quick troubleshooting
The cold water (freezing) machine shows a reverse phase loss fault, which is a common fault of abnormal power supply. The reason for this failure is simple, and it is very convenient to repair, as long as there is a little electrician foundation, it can bﰨ2 䀀 湠疖
-
08/08/2020
Ten matters needing attention in the use of liquid nitrogen tanks
Liquid nitrogen tanks can generally be divided into liquid nitrogen storage tanks and liquid nitrogen transportation tanks. The storage tank is mainly used for the static storage of indoor liquid nitrogen, and is not suitable for long-distance transportatﰨ2 䀀 湠疖 V ǜ V
-
08/08/2020
Standard Design and Installation Specification for Cold Storage
The cold storage design specification enters the construction site, and according to the construction drawings, the implementation status is verified, and the equipment installation location (storage body, drain door, evaporator, host, condenser, control ﰨ2 䀀 湠疖 V ǜ V
-
08/08/2020
Six common problems of central air conditioning
Six common problems of central air conditioning 1. The dew point temperature of the central air-conditioning machine is normal or low, and the reason for the slow indoor cooling and the solution
-
08/08/2020
Selection and calculation of differential pressure regulating valve for central air-conditioning chilled water system
In order to ensure that the flow of the chiller in the central air-conditioning chilled water system is basically constant; the operating conditions of the chilled water pump are stable,
-
08/08/2020
Reasons for condensation at the bottom of the condenser
Reasons for condensation at the bottom of the condenser 1. It is abnormal if condensation occurs at the bottom of the condenser when the unit is running. It may be the reason for the low amount of refrigerant.
-
08/08/2020
Precautions for operation of cold storage condenser
Precautions for operation of cold storage condenser 1. When the refrigeration system is running, all the other valves of the condenser should be opened except the oil drain valve and the air valve closed.
-
08/08/2020
Operation steps of temperature shock test chamber refrigeration unit blowdown and leak detection
Operation steps of temperature shock test chamber refrigeration unit blowdown and leak detection The operation steps of temperature shock test chamber refrigeration unit blowdown and leak detection are as follows:
-
08/08/2020
Maintenance method of central air conditioner without reflection
The L and N resistances are infinite, and the fuse may be burned out or the transformer (Transformer) may be burned out.
-
08/08/2020
Maintenance knowledge and failure methods of small combined cold storage
1. The cold storage door is not closed tightly. Please adjust the distance between the hinge and lock on the door and the storage body.
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
GOODSKY Relay GZT-SH-124LM
AirTAC Air Cylinder MAC32X175S
Honeywell Sensor CSLA2EN
STNC Air Cylinder MGPM20-25