Output Voltage("H"):[(Supply Voltage) -2.5 V] or more
Output Voltage("L"):0.4 V or lower
Output Current(Sink "L"):Up to 30 mA
Output Current(Source "H"):Up to 10 mA
KOYO Compact Universal Incremental Rotary Encoder TRD-J750-RZWS
People who bought this item also viewed
Nemicon Encoder HEF-2048-2MHC
Lika Encoder CK58-H-400ZCU415RPKL7
Renishaw Encoder RESA30USA255B
Sanyo Denki Servo Motor P50B05020DCS1J
Mitsubishi Servo Drive MR-J2S-700B-S096
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
AZBIL Relay FRS100C154-2
Recent related posts
-
08/09/2020
Rosemount 3144P temperature transmitter FF fieldbus manual!
power supply Rosemount temperature transmitter FOUNDAIION fieldbus uses standard fieldbus power supply. The operating voltage of the transmitter is 9 to 32Vdc with a maximum of 11 mA. The rated voltage at the transmitter end is 42.4V dc, Wiring diagram
-
06/27/2020
Compressor installation
Chapter 1 General Provisions Article 1 This chapter is applicable to the installation of reciprocating piston type, screw type, vane type and membrane type positive displacement compressors.
-
09/09/2020
Calculation method for determining air consumption of air compressor
The traditional method of determining the compressed air requirements of a new plant is to add up the air consumption (m³/min) of all air-consuming equipment, and then consider adding a safety, leakage and development factor.
-
09/09/2020
The influence of machining on fatigue life
The residual compressive stress introduced by shot blasting/shot peening is a percentage of the final tensile stress strength, and this ratio increases as the strength/hardness of the part material itself increases. High-strength/hardness metals are more brittle and more sensitive to surface defects. Shot blasting/shot peening will allow these high-strength metals to be used in fatigue-prone working conditions. Aircraft landing gear is usually designed with a fatigue strength of 300 ksi (2068 MPa), combined with shot blasting/shot peening.
-
06/14/2020
Surface roughness is one of the reasons for the fracture of crankshaft of high-pressure air compressor
The crankshaft is the most complicated part of the high-pressure air compressor, and its stability is directly related to the stability of the entire aerodynamic system. What we are mainly involved here are the matters that should be considered when des ﰸ2 䀀 ᅵ皥 䖒皦즠Ʋ娼ི 㲈Ʋ
-
01/03/2021
The knowledge about the intake valve of the screw air compressor is here
The air compressor intake valve can also be said to be an intake control combination valve, which has functions such as intake control, loading and unloading control, capacity adjustment control,
-
02/27/2021
Working principle of servo motor (how servo motor works)
The rotor inside the servo motor is a permanent magnet. The U / V / W three-phase electricity controlled by the driver forms an electromagnetic field. The rotor rotates under the effect of this magnetic field. At the same time, the encoder of the motor feeds back the signal to the driver. The driver adjusts the rotation angle of the rotor according to the comparison between the feedback value and the target value. The accuracy of servo motor depends on the accuracy of encoder (number of lines).
-
09/08/2020
Where is the future of the air compressor industry
First: In today's fierce competition, we must vigorously support private air compressor manufacturers, restrict the development of state-owned enterprises in areas related to the national economy and people's livelihood, and vigorously encourage private enterprises to participate in non-competitive industries.
-
08/11/2020
The role of these parts in cold storage construction
Speaking of cold storage, we must all know that in the field of food in our daily life, it brings us not only convenience in life, but also health and safety. Everyone knows that any piece of equipment will need a lot of large and small parts,
-
08/14/2020
Trouble shooting and correct selection method for thermal expansion valve debugging
As we all know, the thermal expansion valve is one of the four major components in the refrigeration system. It is responsible for reducing the refrigerant from the condensing pressure to the evaporating pressure in the system