How does the factory manage the air compressor room
As an important form of energy generation, air compressors are widely used in various industries, and there are many details in their maintenance. The service life of the air compressor can be prolonged after maintenance. Therefore, how to manage the air compressor room also plays a certain role in the maintenance of the air compressor. In this regard, we make several suggestions:
1. Choose a wide and well-lit place to facilitate the space and lighting required for the operation, maintenance and repair of the air compressor.
2. The ground in the air compressor room must be flat and hard (generally a cement floor is sufficient). At the same time, care should be taken to keep the ground clean and free of debris, especially inflammable and explosive products. Fire extinguishers and other facilities should be equipped to make the room The security is guaranteed.
3. The placement of the air compressor should be careful not to close to the wall, and a certain distance should be reserved to ensure a certain amount of ventilation and maintenance space, which is also conducive to the maintenance and maintenance of the air compressor.
4. The air compressor room should maintain a certain ambient temperature, which should not be higher than 35°C, and should not be lower than 0°C. Note that the temperature of the air compressor room should be kept as low as possible. The air compressor absorbs higher temperature air and reduces the exhaust air volume.
5. The place where the machine room is located should be kept dry, well ventilated, with little dust, and fresh air. Try to avoid dusty, oily, and humid environments to reduce damage to the air compressor, thereby prolonging its service life, and not allowing air The compressor sucks in corrosive gases, paint molecules, and gases that are explosive or unstable in chemical composition or steam, so as not to endanger the air compressor users or cause rapid damage to the unit.
6. The operator should not operate and maintain the air compressor until he has read the operation manual thoroughly. When there is a change (including the operating state), he must immediately notify the equipment after-sales service personnel. At ordinary times, attention should be paid to regular maintenance and maintenance of the parts of the air compressor to keep the machinery and equipment in the best operating state.
7. The pressure pipeline in the air compressor room is strictly prohibited from bumping, and it is strictly forbidden to disassemble and install under the condition of electrification and pressure.
8. Even in a reasonable use environment, the compressed air will still contain a large amount of water and trace oil, which will reduce the production efficiency and product quality of the factory, let alone use the untreated air directly for breathing air or Food contact, therefore must install the corresponding compressed air purification treatment equipment.
9. Only the original equipment, compressor oil and other materials produced by SAPU can be used for maintenance and repair work.
Please recognize the use mark, and its description can be found in the "Operation Manual" of the compressor
09/10/2020
As an important form of energy generation, air compressors are widely used in various industries, and there are many details in their maintenance. The service life of the air compressor can be prolonged after maintenance. Therefore, how to manage the air compressor room also plays a certain role in the maintenance of the air compressor.
09/10/2020
As a new type of cooling and heating method, water source heat pump should be quite mature and no problem from a technical point of view, especially from the point of view of heat pump units. However, considering China's national conditions and the promotion and application of water source heat pump cooling and heating as a whole system, there are still some problems:
09/10/2020
Chapter One Typical Process of Ethylene Plant The first section sequence separation process Section 2 Front deethane process Section 3 Front depropanization process Section 4 Low investment separation process Section 5 Progressive separation process Section 6 Oil absorption and separation process Section 7 Comparison of six separation processes
09/10/2020
Air compressor is abbreviated as air compressor. As a general-purpose mechanical equipment, it is widely used in the field of industrial and agricultural production. The problem is that the motor (three-phase asynchronous motor) as the power equipment of the air compressor generally has a higher failure rate than other motors.
09/10/2020
The vacuum oil purifier is designed according to the different principles of the boiling point of water and oil. It consists of a vacuum heating tank fine filter, condenser, primary filter, water tank, vacuum pump, oil drain pump and electrical cabinet.
09/10/2020
A heat pump is a device that utilizes low-grade heat energy. The use of heat pumps to produce hot water can greatly reduce the consumption of primary energy and the CO caused by burning fossil fuels. Emissions. In China, the application and promotion of heat pump systems has entered a rapid growth track.
09/10/2020
Common failures of dryers for air compressor accessories and equipment The dryer is an important part of the okmarts.com air compressor accessory system and plays an irreplaceable role in the operation of the air compressor. Once the dryer fails, we must immediately organize personnel to repair the dryer.
09/10/2020
Abstract: During the operation of the compressor, some failures and even accidents will inevitably occur. A fault refers to an abnormal condition that occurs during the operation of the compressor, which can be restored to normal operation once the compressor is eliminated, while an accident refers to a damage situation. The two are often related, and if the fault is not eliminated in time, it will cause a major accident.
09/10/2020
1. Compressed air Refers to air with an absolute pressure greater than 0.1Mpa Second, the prescribed working conditions of the screw air compressor Inspiratory pressure: 0.1Mpa (absolute pressure)
09/10/2020
Synthetic lubricants are used in positive displacement devices, lubricant processing and hydrocarbon gas compressors are controversial. Many of these applications require synthetic products to limit toxic catalysts, reduce gas solubility and thereby lead to loss of viscosity and limit reactions with gases.
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
HENGSTLER Encoder AC58/1212EK.42SGA
Schneider Sensor XS212SANAM12
TPG Electric Motor WM-050-060-020S
SBC Linear Guideway SBI45FLL-C-K1