ABB motor is a kind of electromagnetic device which realizes the conversion or transfer of electric energy according to the law of electromagnetic induction
ABB servo motor is installed as follows:
03/02/2021
ABB motor is a kind of electromagnetic device which realizes the conversion or transfer of electric energy according to the law of electromagnetic induction ABB servo motor is installed as follows:
03/02/2021
The connection of the servo motor using Arduino is as follows: Connect the black wires on the two servo motors to the GND on the Arduino Connect the red wires on the two servo motors to the 5V pin on the Arduino Connect the yellow wire on the first motor to pin 8 on the Arduino
03/02/2021
1.Positioning or residual torque: when there is no current passing through the winding, the torque required to make the output shaft of the motor rotate. 2.Driver: an electrical control device used to run the stepping motor. This includes power supply, logic programmer, switching element and a variable frequency pulse source which determines the step rate. 3.Dynamic torque: the torque produced by the motor at a certain step rate. The dynamic torque can be expressed by PULL IN torque or PULL OUT torque.
03/01/2021
1.Oil and water protection of servo motor 1) The servo motor can be used in the place that will be attacked by water or oil drops, but it is not completely waterproof or oil-proof. Therefore, the servo motor should not be placed or used in the environment of water or oil invasion. 2) If the servo motor is connected to a reduction gear, the oil seal should be filled when using the servo motor to prevent the oil of the reduction gear from entering the servo motor 3) The cable of servo motor should not be immersed in oil or water.
03/01/2021
As an open-loop control system, stepping motor has essential connection with modern digital control technology. In the current domestic digital control system, stepping motor is widely used. With the emergence of all digital AC servo system, AC servo motor is more and more used in digital control system. In order to adapt to the development trend of digital control, stepping motor or full digital AC servo motor is mostly used as the executive motor in motion control system. Although they are similar in control mode (pulse train and direction signal), they are quite different in performance and application. This paper compares the performance of the two.
03/01/2021
The output power of Panasonic AC servo motor is generally 0.1-100 W, and the power frequency is divided into 50 Hz, 400 Hz, etc. It is widely used in various automatic control and recording systems 1.Miniaturization design 1) Through the best thermal analysis of the driver, the miniaturization is realized. Compared with the past, the volume is 75% and the weight is 80% 2) The new punching process of thin die steel plate has greatly reduced the iron loss, shortened the motor length (70% in the past) and reduced the number of drive models. It adopts current grading method to prepare and maintain. One driver is suitable for multiple motors and can identify automatically.
03/01/2021
(1) High power factor and high efficiency; (2) Simple structure and reliable operation; (3) Small size, light weight and small loss. Compared with other kinds of motors
03/01/2021
Different definitions: (1) Brushless DC motor is a typical mechatronics product, which is composed of motor body and driver. Brushless motor refers to the motor without brush and commutator (or collector ring), also known as commutator less motor. As early as the 19th century, when the motor was born, the practical motor was the brushless form, that is, the AC squirrel cage asynchronous motor, which has been widely used. However, the asynchronous motor has many insurmountable defects, so that the development of motor technology is slow. The transistor was born in the middle of last century, so the brushless DC motor using transistor commutation circuit instead of brush and commutator came into being. This new type of brushless motor is called electronic commutation DC motor, which overcomes the defects of the first generation of brushless motor.
03/01/2021
Brushless direct current motor (BLDCM,) gets rid of the inherent shortcomings of the brushless DC motor, and replaces the mechanical motor rotor with the electronic motor rotor. Therefore, the brushless DC motor not only has the excellent speed characteristics of the DC motor, but also has the advantages of simple structure, no commutation flame, reliable operation and easy maintenance.
02/27/2021
The rotor inside the servo motor is a permanent magnet. The U / V / W three-phase electricity controlled by the driver forms an electromagnetic field. The rotor rotates under the effect of this magnetic field. At the same time, the encoder of the motor feeds back the signal to the driver. The driver adjusts the rotation angle of the rotor according to the comparison between the feedback value and the target value. The accuracy of servo motor depends on the accuracy of encoder (number of lines).
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SUNX Sensor CX-421-C5
SMC Solenoid Valve SY3160-5LZ-M5
Eaton Vickers Vane Pump V10-1P5P-38A20L
KCL Vane Pump VQ25-65-F-RAL-01
