Model:F3SJ-A0470P30
Number of Beams:19
Protective Height[mm]:470
Response Time[ms]:
ON OFF *1: 11
OFF (Synchronized) ON *2: 44
Current Consumption[mA]
Emitter : 76
Receiver: 68
Beam Gap(p):25 mm
Omron Light Curtain F3SJ-A0470P30
People who bought this item also viewed
YINGB Light Curtain GMNB-10-4-N
YINGB Light Curtain GMNB-18-4-N
Freescale NXP Sensor KMA320
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
SMC Solenoid Valve SY5420-4DZ-01
Kelon Air Conditioner KFR-50GW-QW1-X3
SMC Solenoid Valve VFR3140-4G
Eaton Vickers Vane Pump V10-1S7S-1D20L
BANDO Belt T5-610-6
Recent related posts
-
06/14/2020
What are the causes of frost in refrigeration compressors
The importance of refrigeration compressors in the entire cold storage refrigeration system is self-evident, I believe everyone knows. Next look at the editor to teach you to turn around.
-
08/29/2020
Compressed air technology is moving towards an era of high efficiency
Compressed air is the most widely used energy source in industry and commerce, in addition to electricity. Its wide application stems from its easy operation, fast speed, high power density, safety and good compatibility, but its higher cost cannot be ignored...
-
09/15/2020
Reasons and necessity of overhaul of oil-injected twin-screw air compressor
The structure of the main engine (also known as the head) of an oil-injected twin-screw air compressor is usually composed of a pair of mutually meshing screws, main engine casing, high-pressure end and end cover, and low-pressure end and end cover.
-
01/18/2023
The Differences between Solenoid Valves and Motorized Valves
The solenoid valve is an industrial equipment controlled by electromagnetic, which is the basic component of automation used to control fluid.
-
06/14/2020
Is PVC or PE good for domestic fresh air system pipes
Is PVC or PE good for domestic fresh air system pipes Fresh air system is a category of light equipment and heavy design. Fresh air equipment is highly dependent on design and construction.
-
09/05/2020
What is the difference between single screw compressor and twin screw compressor
Single-screw and twin-screw manufacturing process of twin-screw is more complicated than single-screw in terms of structure, and the difference in service life and working efficiency is not very big,
-
06/16/2020
Working principle of automobile compressor
Working principle of automobile compressor Car compressor The function of automobile compressor is to transform the low-temperature and low-pressure gas refrigerant from the evaporator into high-temperature and high-pressure gas refrigerant through comp 器2 䀀 ᅵ皥 䖒皦즠Ʋ㉄ᰙ
-
07/17/2020
How to maintain the refrigeration system on a daily basis
Many users have no professional personnel or simple maintenance of the refrigeration system when using the refrigeration system, which causes the system to be directly paralyzed once the problem occurs, and can not be used directly. It also takes a lot of manpower and material resources to solve, and it is very time-consuming.
-
09/18/2020
What are mineral oil, semi-synthetic oil and fully synthetic oil What is the difference between them
What are mineral oil, semi-synthetic oil and fully synthetic oil What is the difference between them Mineral oil (MineralLubricant) Mineral oil is a lubricating oil extracted from petroleum. The base oil of mineral oil is the bottom oil left over after the fractional distillation of useful light substances (such as aviation oil, gasoline, etc.) during crude oil refining. Into the product. Essentially, it uses the poorer components of crude oil. Mineral oil is currently the most common type of lubricant on the market.
-
08/08/2020
Reasons for condensation at the bottom of the condenser
Reasons for condensation at the bottom of the condenser 1. It is abnormal if condensation occurs at the bottom of the condenser when the unit is running. It may be the reason for the low amount of refrigerant.