KENNAMETAL Tool for Metal Cutting LN11-C25-26-160-3T
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
DHF Tool for Metal Cutting UTH0504
SAMYOUNG Capacitor 63V 150UF
BANDO Belt STS S2M-524-200
Recent related posts
-
09/06/2020
How can air compressors save energy and electricity
In recent years, energy conservation and environmental protection have been pushed to the forefront. With the strong support of national policies and the increasing awareness of energy-consuming enterprises
-
08/11/2020
Radiator heating system riser pipe installation and precautions
1. Standpipe installation of radiator heating system:<br></br> 1. When arranging the system riser, it should be matched with the use requirements of the building, the heating system diagram, the layout of the radiator, etc.. It is necessary to save pipes and facilitate installation and maintenance.
-
06/14/2020
Which air cooling effect is better than air conditioning
The air energy heat pump cooling and heating machine is the same as the air conditioner, which can both heat and cool. The heating function is the strength of the air energy cooling and heating machine, and the effect is naturally needless to say. But wha 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥 巠皱㙲皦抐皱 巠
-
06/14/2020
Frequently asked questions about refrigeration compressors Do you know these?
1. Why control the impurity content and moisture content of the compressor and air conditioning system?
-
09/08/2020
Types and functions of adsorbents for drying machines
The working principle of the suction dryer (also known as the adsorption dryer) is to reduce the moisture content in the compressed air by using the characteristics of the adsorbent to absorb moisture. Generally speaking, the pressure dew point of the outlet air of the suction dryer reaches -20℃~-70℃ .
-
07/13/2020
Danfoss medium temperature refrigeration compressor M series
liquid 1. Liquid back: When the refrigerant returned to the compressor is not a pure gas state, but contains liquid, the influence of the liquid refrigerant on the compressor is negative. If there is too much liquid, it may even cause liquid shock, even if there is no liquid shock, it will happen. Wet compression causes oil to run away.
-
10/18/2021
Maintenance of Absolute Encoders
What are the precautions for maintenance of rotary encoders? Rotary encoders are used as speed and displacement feedback sensors, which are mainly applied in servo motors, asynchronous motors
-
07/19/2020
Basic knowledge of refrigeration compressor
After shutting down, stop for at least 3 minutes before starting again to eliminate the pressure difference between the compressor inlet and outlet. Because in the case of a large pressure difference, the starting torque of the motor will increase, causing the current to rise to a certain level, the protector will act and the compressor cannot continue to run.
-
02/09/2022
7 Reasons Why an Air Compressor is Overheating
As hot summer is coming, air compressor maintenance workers will also usher in the busiest season of the year.
-
01/25/2024
Industrial Control Cabinet Cooling: How to Design the Cooling and Ventilation System?
Control cabinets, such as wind turbine electrical control cabinets, realize system power distribution, monitoring and control of the entire unit.