What parameters should be understood when choosing a central air-conditioning air-cooled heat pump unit
You must be familiar with central air-conditioning, but did you know that there is a unit in central air-conditioning called a cold and heat pump unit? The work of central air-conditioning is inseparable from it. Many friends may want to know the air-cooled heat pump unit of central air-conditioning. What is the basic performance, so here is the editor of okmarrs.com to introduce to you.
folding heat and cold
This parameter is the most critical parameter that determines the normal use of the air-cooled heat pump. It refers to the cooling capacity or heating capacity of the air-cooled heat pump unit and the inlet and outlet water temperatures under the design conditions. It can be found from the product samples provided by the relevant manufacturers. However, it is also found in the design that the sample parameters provided by some manufacturers have not been tested but copied from relevant samples of other manufacturers. This brings certain difficulties to the correct selection of designers.
Therefore, the editor of okmarts.com suggests that, if possible, the designer can obtain the variable-condition performance curve of the compressor from the compressor manufacturer according to the compressor model configured by the air-cooled heat pump of the relevant manufacturer. According to the heat pump Check the cooling capacity and heating capacity of the compressor under the design conditions of the heat pump to determine the authenticity of the parameters provided by the sample.
folding COP value
This value is an important parameter to determine the performance of the air-cooled heat pump. The value of its value directly affects the power consumption of the air-cooled heat pump. Therefore, the unit with a high COP value should be selected as far as possible. At present, my country's national standard is that the COP value is 2.57. The COP of most imported or joint venture brands is around 3, and the value of high-efficiency units of individual imported brands can reach 3.8.
folding noise
Noise is also an important parameter to measure an air-cooled heat pump unit, and it is directly related to the impact of the heat pump on the surrounding environment. Relevant domestic experts once classified the noise of various imported heat pumps into three levels based on actual engineering measurements. The first level is above 85dB, the second level is between 75-85dB, and the third level is below 75dB. We should prioritize the selection of units with noise below 80dB in the selection of engineering design.
Folded size
Most of the air-cooled heat pump units are arranged on the outdoor roof. When the equipment is arranged, the distance between the equipment and the surrounding wall and the distance between the equipment have clear requirements. Therefore, we must consider whether the selected equipment size is Meet the size requirements of equipment layout. Under the premise of the same performance, smaller units should be selected first to reduce the equipment footprint.
folding running weight
As most of the air-cooled heat pump units are arranged on the roof, the load-bearing capacity of the roof must be considered when selecting the type. If necessary, the structural professional should be negotiated to enhance the load-bearing capacity of the roof. However, when selecting equipment, we should give priority to units with lighter operating weight.
What parameters should be understood when choosing a central air-conditioning air-cooled heat pump unit
Recent related posts
-
08/16/2020
What parameters should be understood when choosing a central air-conditioning air-cooled heat pump unit
You must be familiar with central air-conditioning, but did you know that there is a unit in central air-conditioning called a cold and heat pump unit? The work of central air-conditioning is inseparable from it.
-
08/16/2020
What should I do if the screw of the rod-type chiller bites to death
Screw chillers are widely used in industry and chemical industry. Screw chiller is just one type of screw refrigeration series. There are also medium and low temperature screw chillers, air-cooled screw chillers,
-
08/16/2020
What to pay attention to when the refrigeration equipment is moved
Because the company needs to change the working environment, all the equipment of the company must be moved, and the refrigeration equipment in the disassembly and installation process requires staff with rich professional knowledge,
-
08/16/2020
Where is the key technology of ammonia refrigeration system construction
1. Refrigeration compressor installation Before the refrigeration compressor is in place, clean the soil and dirt from its bottom and foundation bolt holes, and clean up the foundation surface that has passed the acceptance.
-
08/16/2020
Why is the temperature too low after the cold storage is installed
After the cold storage is built, the first thing should be tested, so that we can know whether there will be problems after the cold storage is installed. Such a problem needs to be considered in the initial stage of the general cold storage installation.
-
08/15/2020
What should I do if wall cracks appear after the cold storage is built
After the construction of the cold storage project, there may be many problems. For example, we have seen a lot of news recently. It is said that the wall cracks appeared after the construction of the cold storage
-
08/15/2020
What should I do if the refrigeration performance of industrial refrigerators declines
When many enterprise users use industrial refrigerators, due to the lack of knowledge about the use and maintenance of equipment, industrial refrigerators are prone to various failures
-
08/15/2020
What should I do if the refrigeration equipment does not operate normally
Nowadays, in order to prevent the goods from selling well and causing economic losses, more and more businesses are using Xuzhou refrigeration equipment to store excess goods or sell them in anti-seasonal times.
-
08/15/2020
What should I do if the cold storage is moldy How to physically remove mildew
Mold generally grows in dark and humid places and can adapt to lower temperatures. Usually in high temperature storage, the situation is serious. Mold grows in the cold storage, and the spores will fly everywhere, which will contaminate the goods and products stored in the storage.
-
08/15/2020
What should be paid attention to when handling refrigeration equipment
Precautions for the handling of refrigeration equipment-Do not put it down during transportation. A series of matters must be paid attention to during the transportation of refrigeration equipment.
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
Sanyo Denki Fan 109BJ24MC2
Pilz Relay 777148
Parker Servo Drive CP-OEM350
MASTRA Water Pump R85-QS-10
HITACHI VFD Frequency Converter NJ600B-1850HFF
AirTAC Air Cylinder SULF50X450