Connection size: Rc 1/8 / R 1/8
Fixed orifice size: 0.7 mm
Effective area: 0.38 mm2(valve operate)/2.64 mm2(valve not operate)
Fluid: air
Max. operating pressure range: 0 to 0.7 MPa
Max. opearting vacuum pressure range: 0 to -100 kPa
Max. operating flow rate: 8 L/min(ANR)
SMC Safety Valve ZP2V-B01-07
Customers frequently viewed
IWAYA DENKI Water Pump 25CJT0752
Panasonic Servo Motor MHMF022L1V2M
Honeywell Solenoid Valve VE4025B1045
ROTEN Mechanical Seal 8E5K-22-X
SANDSUN Overload Pump VA08H-760
GS Battery 6-QW-60(450)-(55D23L-KR)
Rechi Compressor 44R273A
MINDMAN Air Cylinder MCQV2-11-40-200
Mitsubishi Compressor YB645WTG
KEYENCE Relay KV-8EYR
VAISALA Transmitter DMT142
MINDMAN Air Cylinder MCJT-11-20-60
BANDO Belt STS S3M-378-9
Recent related posts
-
01/09/2021
Be sure to understand these before installing a new fan
The most troublesome thing: the new fan requires indoor and outdoor air exchange, which requires opening holes on the wall or glass. The diameter of the holes in the market is basically concentrated on 150mm\120mm\110mm\100mm.
-
01/12/2022
Top 10 Servo Motors in Industrial Automation
Servo motor is an engine that controls the operation of mechanical components in the servo system, which is a kind of indirect speed change device to supplement the motor.
-
06/13/2020
Analysis of the current status of refrigeration compressor technology development
Analysis of the current status of refrigeration compressor technology development
-
08/13/2020
Acceptance standards after the cold storage design and installation are completed
A newly built cold storage, when it's time for acceptance, it will definitely be anxious. How can it be accepted to ensure quality and quantity? The editor of okmarts.com will briefly introduce it below.
-
08/11/2020
Let's take a look at how important the power control of industrial chillers is!
Industrial chillers are used in plastics, electronics, chemicals, electroplating, food preservation, textiles, printing, medicine, construction, machinery supporting equipment and other industries.
-
06/13/2020
What is the difference between heating 24 ℃ and cooling 24 ℃
Regardless of the room temperature, as long as the air conditioner is in the cooling mode and is in a working state, the wind blown out is cold wind. To put it bluntly, the temperature of the blown air is determined by the operation mode of the air condit 器2 䀀 ᅵ皥 䖒皦즠Ʋ煔क़ 㲈Ʋ 䌁皦 ᮔDž༬皧煞क़Ѐ 呄ᠾ鹨់༹皧 ࠄ 00령ꐱ댁珵뛐珵Љ 䕄ྦ 뤂ᐱ뚜珵 ᴴᏩ呄ᠾ퍘ᒥ 鹨់ᩄ ꋔྦ 瑉浥
-
03/01/2021
Related technical terms
1.Positioning or residual torque: when there is no current passing through the winding, the torque required to make the output shaft of the motor rotate. 2.Driver: an electrical control device used to run the stepping motor. This includes power supply, logic programmer, switching element and a variable frequency pulse source which determines the step rate. 3.Dynamic torque: the torque produced by the motor at a certain step rate. The dynamic torque can be expressed by PULL IN torque or PULL OUT torque.
-
07/05/2022
Installation Of Magnet Pump
1.Dropping or subjecting the pump to strong impact may result failure. Handle the pump with care.
-
07/25/2020
The influence of evaporating temperature on refrigeration system
Household air conditioners generally cannot adjust the evaporation temperature! The cold storage and other devices can be adjusted in small amounts, and the increase in the evaporation temperature is mainly in the design and manufacturing stage!
-
12/14/2023
Troubleshooting Loud Server Fans: Causes and Solutions
In the realm of technology, servers serve as the backbone of numerous industries, powering everything from websites to data centers.